The first sign of a hidden water leak is rarely a puddle. It is usually a high water bill that makes no sense, three months after the leak started.
The good news is you can confirm whether you have one in about half an hour, with nothing more than your water meter. Here is how, what the usual culprits are, and how to get some of that money back.
Step one: read your bill properly
Before anything else, find the average daily use figure on your Sydney Water bill and compare it with the same quarter last year. Summer is always higher than winter, so compare like with like.
If usage has jumped noticeably and nothing has changed at home, like no new housemate, no new garden and no pool being filled, that is worth investigating. A slow leak running around the clock adds up quickly. If the meter test confirms it, a local plumber Eastern Suburbs homes rely on can trace it without opening walls.
Step two: the 30-minute water meter test
This water meter test tells you, with no guesswork, whether water is leaving your property when nobody is using it.
- Turn off every tap, and make sure the dishwasher, washing machine and any irrigation are not running.
- Find your meter, usually near the front boundary in a house. Write down the full reading, or take a photo.
- Wait at least 30 minutes without using any water. Overnight is even better for slow leaks.
- Read it again. If the numbers have moved, water is escaping somewhere past the meter.
In an apartment, the meter may be in a riser cupboard or a bank of meters in the garage, and some older blocks share a single meter across the building. If you cannot identify yours, the strata or building manager can.
Step three: rule out the easy ones
If the meter moved, check the cheap culprits first. Between them they account for a large share of the unexplained bills we see.
A running toilet
A worn inlet valve or flush seal can let water trickle into the pan all day without any noise. Put a few drops of food colouring in the cistern and wait 15 minutes without flushing. Colour in the pan means the cistern is leaking. It is a small toilet repair, not a big job.
The hot water relief valve
A little discharge from the relief valve on a storage hot water system is normal. Constant dribbling is not, and it can run straight into a drain where you will never see it. We cover this in more detail in our hot water system guide.
Outside taps and irrigation
A garden tap with a failed washer, or a buried irrigation line with a split fitting, is an easy one to miss because the water soaks straight into the soil.
Meter still moving with everything turned off? The leak is somewhere you cannot see. Find it before it does damage to walls, floors or footings.
Where hidden leaks actually hide
If the simple checks come up clean, the leak is almost always in one of these places.
- The supply line between the meter and the house. Often the oldest pipe on the property. Watch for a patch of lawn that stays green through a dry spell, or a soft spot in a garden bed.
- Pipes under a slab. A slab leak on a hot line can show up as a warm patch on a tiled floor. On a cold line it may show nothing at all until the bill arrives.
- Inside walls. Swollen skirting boards, bubbling paint, a musty smell or a patch of mould that keeps coming back can all point to a leak behind a wall.
- Pinhole leaks in copper. Small corrosion holes in older copper pipe can spray into a wall cavity for months.
- Shower mixers and failed waterproofing. These often show up in the room next door, or the ceiling below, rather than in the bathroom itself.
Why the Eastern Suburbs makes this harder
A few things about the housing here turn a simple leak into a hard one to find.
- Old galvanised and copper supply lines. Many terraces and semis in Randwick, Paddington and Woollahra still run original or decades-old supply pipe that corrodes from the inside.
- What sits on top. A supply line under sandstone paving or a tiled front path in Clovelly or Bronte is exactly where you do not want someone digging on a guess.
- Apartments. A leak in a common property pipe can show up on one lot's bill, or on a shared building meter, and the source may be in another apartment entirely.
How a plumber finds it without wrecking the place
Proper leak detection is about narrowing down before opening up. That usually means isolating sections of the supply to see which one is losing water, then pinpointing the exact spot.
- Acoustic leak detection listens for the sound of water escaping under pressure, through concrete, tiles and soil.
- Thermal imaging picks up temperature differences, which is especially useful for hot water leaks under floors and in walls.
- Pressure testing confirms whether a section of pipe is holding pressure or losing it.
The point of all of it is to open up one spot rather than guess at five. Under a heritage tile floor or a sandstone courtyard, that difference matters a great deal.
Getting some of the bill back
If a licensed plumber finds and repairs a hidden leak on your property, Sydney Water lets you apply for a hidden leak allowance on your bill.
To give yourself the best chance, keep the plumber's invoice showing what was found and repaired, make sure it describes the leak as concealed, and photograph the meter reading once the repair is done. Obvious leaks like a dripping tap or a running toilet generally do not qualify.
Quick answers
How do I know if I have a hidden water leak?
Turn off every tap and appliance, note your water meter reading, and check it again after 30 minutes without using any water. If the reading has moved, water is escaping somewhere on your property. A bill that has jumped with no change in how you use water is the other big clue.
Can I fix a hidden leak myself?
Sydney Water notes that homeowners can legally do only minor work, like changing a tap washer. A leak inside a wall, under a floor or in the supply line needs a licensed plumber, and a licensed repair is also what you need to apply for the hidden leak allowance.
Will Sydney Water refund my high water bill?
Not in full, but if a licensed plumber finds and repairs a concealed leak, you can apply for a hidden leak allowance that credits part of the excess usage. Keep the plumber's invoice and a photo of the meter after the repair.
Is a leaking water meter my responsibility?
Sydney Water owns the meter, but leaks at the meter tap are the owner's to fix. Sydney Water says it will fix the meter tap for free if you call 13 20 90, or you can have a licensed plumber do it sooner at your own cost.
Do the meter test this weekend
It takes 30 minutes, costs nothing, and tells you straight away whether you have a problem. Do it once a season, and definitely before you go away for a while.
If the meter moves and you cannot find why, call us on 0402 556 935 and we will track it down.